Sale

Grip Handle Calibration Weight 20kg Class1

20 kg Grip Weight, Class 1, Tolerance ± 50 mg, 2 piece construction with handle, 303 stainless steel. Test weight does not come with certificate but one may be purchased for an additional cost by clicking the box below.

Availability: 0 left in stock. Usually ships in 2 weeks

MSRP: $1,399.00

YOU PAY: $1,205.00

You save $194.00

Useful Downloads
Calibration certificate comparison table
Traceable certificate SAMPLE
NVLAP calibration certificate SAMPLE

* Required Fields

Details
Details
20 kilogram grip handle weight is ideal for calibrating scales that require a 20 kg calibration weight. Class 1 NO CERTIFICATE (available at additional cost). This grip handle weight is made from 303 stainless steel . Please note if your company has a quality assurance program you will probably need to purchase the OPTIONAL Certificate to meet compliance of regulatory and quality control requirements. We highly recommend you check with your regulatory compliance officer or ISO Auditor for guidance for your specific quality assurance/quality control requirements or when in doubt just purchase the OPTIONAL NVLAP Calibration Certificate. Weights are the most frequently used and most important equipment for testing scales and balances. Routine testing for weighing devices like balances and scales is critical to ensuring accurate weighing results and maintaining quality control standards. By placing various test weights you can verify a balance meets the process tolerance in-between regular scale calibrations. Care should always be taken when using test weights by never touching the weight with bare hands (grease and dirt can transfer from fingers to weight) and never slide weights across the weighing platform since you can change the conventional mass value. Traceable Certificate is designed for those laboratories and companies that require traceability, but do not need to meet any stringent regulatory requirements. The Traceable Certificate measurement process is based on a single standard and utilizes one series of comparisons. If you are required to meet standards including NVLAP Handbook 150-2, ISO/IEC 9000, ISO/IEC 17025, FDA, GMP, GLP, DOD, ANSI/NCSL Z540-1, and nuclear requirement a Traceable Certificate will NOT meet the compliance requirements. We always recommend you check with your regulatory or compliance officer to verify what quality or regulatory requirements must be meet before ordering any calibration weights. We always like to say when in doubt purchase weights with the NVLAP Certificate. -------------- Report of Traceability - This report identifies: Tolerance class Type of construction NIST test number Date of applicable primary standard(s) Secondary set number Includes technician's signature Description of the weight(s) Test Number Serial Number Nominal Value Uncertainty of the measurement tolerance Information on weighing procedures Date the primary standards were last tested at NIST and the NIST test number Date and test number for our working standards. Statement of compliance to ANSI/NCSL Z540 and ANSI/ISO/IEC 17025 NVLAP Accreditation Logo and laboratory code. Statement of traceability to the International Prototype Kilogram (IPK) this meets the international requirement for traceability to the International System of Units. -------------- Certificate of Calibration - The Certificate of Calibration includes everything found in a Report of Traceability listed above with the additional information listed below: Uncertainty value Test conditions temperature, barometric pressure, humidity. Conventional Mass Correction Uncertainty of the measurement Identification of the balance used in the calibration as found value if an adjustment is performed assumed density of the weight material weight is made from Pass/Fail result of magnetic testing Volume of the weight Cubical Coefficient of expansion True Mass correction -------------- Difference between Traceability and Certificate of Calibration? The major difference between the Report of Traceability and the Calibration Certificate is the Report of Traceability is a tolerance test and is only available for new weights. The Certificate of Calibration is a full report of the parameters tested. Above we outline what comes with each report. The Certificate of Calibration will, however, give a smaller uncertainty and a more precise value of the actual mass due to the multiple measurements that are made during the calibrating process. If you require a accredited laboratory certificate to meet ISO/IEC 17025 & ANSI/NCSC Z540-1 the you need a NVLAP Certificate of Calibration. To get all the accuracy your electronic balance or digital scale provides, you need to perform routine calibrations and verifications using precision calibration weights. Troemner's Stainless Steel Electronic Balance Calibration Weights are intended for this purpose. ASTM stainless steel electronic balance calibration weights possessing closely controlled density, low magnetic susceptibility, good stability and resistance to corrosion and damage through handling. All of Troemner's Electronic Balance Calibration Weights are type II which have an adjusting cavity to allow for adjustment during future calibrations. Within the weight there is a cavity that is filled with adjusting material, typically the same material from which the weight is made. This cavity is sealed during the production process to ensure the stability of the weight. Electronic Balance Calibration Weights are cylindrical in shape and flat on top, to stack easily on center.
calibration weight shape
Construction and General Shape: Troemner's Electronic Balance Calibration Weights are manufactured from the highest quality stainless steel alloy, possessing closely controlled density, low magnetic susceptibility, good stability and resistance to corrosion and damage through handling. All of Troemner's Electronic Balance Calibration Weights are type II which have an adjusting cavity to allow for adjustment during future calibrations. Within the weight there is a cavity that is filled with adjusting material, typically the same material from which the weight is made. This cavity is sealed during the production process to ensure the stability of the weight. Electronic Balance Calibration Weights are cylindrical in shape and flat on top, to stack easily on center. - Grip handle weights from 5 kg to 30 kg have a recess in the top center of the weight with a lifting handle spanning the recess slightly below the top surface of the weight. The recess allows the user to pick up the weight using the handle and provides clearance for the user's hand. Grip handle weights 5 kg to 10 kg are 5 inches in diameter. Grip handle weights above 10 kg to 30 kg are 6 inches in diameter. The adjusting cavity for grip handle weights is within the lifting handle. - Cylindrical weights from 1 kg to 5 kg are machined as cylinders and have a groove around the diameter approximately 25% from the top of the weight to allow for easier handling. The adjusting cavity opening is in the bottom of the weight for the 1 kg weight and on the top of the weight for the 2 kg through 5 kg. - Weights from 200 g to 500 g are machined as straight cylinders with the adjusting cavity opening in the bottom of the weight.
calibration weights for balance calibration
Surface Finish: Troemner ANSI/ASTM Classes 1 and 2 have all surfaces polished to a perfect, mirror like finish.
calibration weight storage case
OPTIONAL Polypropylene Cases for Individual Weights: To safeguard your Electronic Balance Grip Handle Weights, you can purchase the OPTIONAL Polypropylene Individual Weight Case made of high impact plastic. Cases are made with reinforced metal edges and corners. They also have a padded carrying handle to ensure proper handling. Again these cases are optional and available for weights 5kg through 30 kg. Selecting The Right Weight: - Check you scale's manual or specification sheet to find the weight value required to calibrate your scale. - It is recommended that the weight selected to calibrate a balance and/or scale have a tolerance small enough as not to be detected by the balance and/or scale. Troemner recommends the tolerance of a weight selected for calibrating a balance and/or scale is no more than 1/3 of the readability or precision of the balance and/or scale being calibrated. If this cannot be achieved, it is suggested that a Class 1 Electronic Balance Calibration Weight with a NVLAP certificate be ordered which provides the actual mass value for the weight which reduces measurement uncertainty. - Electronic Balance Calibration Weights can also be used to check or verify the accuracy of your balance and/or scale between calibrations. It is recommended that the user check a balance and/or scale prior to each use. Keeping the weight at or near the balance and/or scale keeps the weight at the same temperature as the equipment. Product photo may not exactly match the product offered for sale. We also offer a huge selection of Laboratory Calibration Weights and Calibration Mass Sets with Calibration certification and NIST Traceable Calibration for lab balances at www.calibrationweight.com All calibration weights are not returnable. Once your order has been placed it CAN NOT be cancelled. Please carefully consider this prior to placing your order. The reason for this is these weights are custom manufactured and are certified on the date they were made. In addition, if you touch the calibration weight with your fingers the oil in your skin would change the tolerance and we can not take this chance if the weight was returned.
You May Also Like
You may also be interested in the following product(s)
20 kilogram stainless steel grip weight 20 kilogram stainless steel grip weight

MSRP: $1,270.00

YOU PAY: $1,074.00

30 Kilogram Grip Weight Class 1 30 Kilogram Grip Weight Class 1

MSRP: $1,972.00

YOU PAY: $1,695.00

30KG Grip Weight Class 2 Stainless Steel 30KG Grip Weight Class 2 Stainless Steel

MSRP: $1,745.00

YOU PAY: $1,485.00

25 piece (1kg-1mg) weight set class 1 nvlap  25 piece (1kg-1mg) weight set class 1 nvlap

MSRP: $4,215.00

YOU PAY: $3,620.00

4 kilogram balance calibration weight 4 kilogram balance calibration weight

MSRP: $359.00

YOU PAY: $299.00

50LB Grip Weight Class F Stainless Steel 50LB Grip Weight Class F Stainless Steel

MSRP: $938.00

YOU PAY: $796.00

10KG stainless steel test weight 10KG stainless steel test weight

MSRP: $835.00

YOU PAY: $705.00

Grip Handle Test Weights 5KG Class 1 Grip Handle Test Weights 5KG Class 1

MSRP: $689.00

YOU PAY: $585.00

25KG Grip Weight Class 2 Stainless Steel 25KG Grip Weight Class 2 Stainless Steel

MSRP: $1,465.00

YOU PAY: $1,238.00

Grip Handle Weight 25kg Class 1 Grip Handle Weight 25kg Class 1

MSRP: $1,687.00

YOU PAY: $1,445.00

8 kilogram calibration test weight 8 kilogram calibration test weight

MSRP: $855.00

YOU PAY: $735.00

cal weight set 16 pc(5kg -1g) class 1 nvlap cal weight set 16 pc(5kg -1g) class 1 nvlap

MSRP: $5,948.00

YOU PAY: $5,196.00

5KG cylindrical calibration weight 5KG cylindrical calibration weight

MSRP: $355.00

YOU PAY: $304.00

Mass Calibration - Weights 4kg Class 1 Mass Calibration - Weights 4kg Class 1

MSRP: $365.00

YOU PAY: $319.00

20 KG Test Weight Class F no certificate 20 KG Test Weight Class F no certificate

MSRP: $170.00

YOU PAY: $142.70

Calibration Weights 10KG Class 1 Calibration Weights 10KG Class 1

MSRP: $931.00

YOU PAY: $804.00

stainless steel 3kg calibration mass stainless steel 3kg calibration mass

MSRP: $287.00

YOU PAY: $239.00

cast iron grip handle 10kg cal weight cast iron grip handle 10kg cal weight

MSRP: $140.00

YOU PAY: $129.00

20 kg scale calibration weight 20 kg scale calibration weight

MSRP: $166.00

YOU PAY: $156.00

1 LB Cast Iron Weight 1 LB Cast Iron Weight

MSRP: $62.00

YOU PAY: $55.00

5 LB cast iron weight class 7 no certificate 5 LB cast iron weight class 7 no certificate

MSRP: $78.00

YOU PAY: $65.00

25 KG Cast Iron Weight Class F no certificate 25 KG Cast Iron Weight Class F no certificate

MSRP: $204.00

YOU PAY: $170.00

10 KG Grip Weight Class F no certificate 10 KG Grip Weight Class F no certificate

MSRP: $155.00

YOU PAY: $130.00

Additional Info
Additional Info
Brand Troemner
Capacity x Readability No
Capacity x Readability (dual range) No
Readability No
Readability 2 No
Weight Modes No
Functions No
Features No
Legal for Trade N/A
Construction 303 stainless steel, 2 piece construction with handle
Calibration No
Communication No
Platform size (inches) No
Power Requirements No
Manufacturer Warranty (years) No
Additional info ASTM Class 1, Tolerance ± 50 mg, Certificate available at an additional cost
Tags
Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Specs
Description: Stainless Steel Electronic Balance Calibration Weights
Weight: 20 kg
Tolerance: ± 50 mg
Class: Class 1
Certification: Troemner NO LONGER offers Statement of Accuracy. OPTIONAL Traceability Certificate or NVLAP Calibration Certificate available at ADDITIONAL COST
Material: 303 stainless steel
Construction: 2 piece construction with handle.
Case: Weight NOT supplied with case. Case available upon request for an additional cost.
 
  Loading...