Sale

Calibration knob weight 50 g - Class 1 NVLAP certificate

Calibration knob weight 50 g, Class 1 NVLAP, two piece stainless steel construction, tolerance ± 0.12 mg. Class 1 NVLAP traceability certificate included with this test weight.

Availability: 0 left in stock. Usually ships in 2 weeks

MSRP: $148.00

YOU PAY: $126.00

You save $22.00

Useful Downloads
Calibration certificate comparison table
NVLAP calibration certificate SAMPLE
Details
Details
Metric precision individual weight 50 gram. Class 1 NVLAP certificate. Tolerance: ± 0.12 mg. Made of alloy 8 highly polished stainless steel. 2 piece construction with handling knob. Weight supplied with case. Troemner's precision weights are sampled regularly throughout the manufacturing process to determine the magnetic properties of the material. Stainless steel is tested for magnetic permeability and for magnetic susceptibility. Once Troemner's two-piece weights are machined and polished, they are checked using a Gaussmeter prior to the calibration. Troemner Alloy 8 stainless steel precision weight material possesses low magnetic susceptibility, uniform consistency and high resistance to corrosion. The calibration weights have extremely low magnetic properties which exceed the requirements of ASTM E617. In addition Alloy 8 has a more consistent density, and is a harder material than materials used by other weight manufacturers. Troemner Alloy 8 Stainless Steel, which was developed by Troemner and is available exclusively through Troemner. It is the finest grade of stainless steel available and is similar to material originally specified in the manufacture of state primary standards. Weight specifications are designed so the specifications on surface finish, markings, construction, material density and magnetic properties get more restrictive as the weight tolerances get smaller in order to enable the weight to maintain its tolerance over time. These weights are designed for your most demanding weighing applications. To get all the accuracy your laboratory balances provide, you need to perform routine calibrations and verifications using precision calibration weights. All of Troemner's Precision Class 1 Calibration Weights are 2 piece construction designed with an adjusting cavity to allow for adjustment during future calibrations. Within the weight there is a cavity that is filled with adjusting material, typically the same material from which the weight is made. This cavity is sealed during the production process to ensure the stability of the weight.
precision lab calibration weights
Construction and General Shape: Troemner Calibration Weights 1 g and larger consist of a body and a lifting knob. The lifting knob is specifically designed for use with forceps, tweezers or some other lifting device. Weight bottoms are slightly recessed to expose the smallest possible area to wear. Each weight is marked with its nominal value. Weights 500 mg and lower are made of sheet metal and are one-piece construction with one side turned up to make them easy to handle with forceps. Depending on the class, these weights may or may not be marked with their nominal value.
precision calibration weights
Surface Finish: All surfaces are polished to a perfect, mirror-like finish and conform to specifications in ANSI/ASTM E617
precision calibration weight storage case
Polycarbonate Cases for Individual Weights: To safeguard your Troemner Alloy 8 Stainless Steel Precision Calibration Weights, attractive, durable, high quality, polycarbonate cases are provided with weights 1 mg through 2 kg. The polycarbonate cases feature a custom insert, bumper, and locking lid to assure weights are held securely within the case and avoid movement. Polycarbonate cases for weights greater than 2kg are available at an additional cost. Selecting The Right Weight: - Check you scale's manual or specification sheet to find the weight value required to calibrate your scale. - It is recommended that the weight selected to calibrate a balance and/or scale have a tolerance small enough as not to be detected by the balance and/or scale. Troemner recommends the tolerance of a weight selected for calibrating a balance and/or scale is no more than 1/3 of the readability or precision of the balance and/or scale being calibrated. If this cannot be achieved, it is suggested that a Class 1 Precision Calibration Weights with a NVLAP certificate be ordered which provides the actual mass value for the weight which reduces measurement uncertainty. - Precision Calibration Weights can also be used to check or verify the accuracy of your balance and/or scale between calibrations. It is recommended that the user check a balance and/or scale prior to each use. Keeping the weight at or near the balance and/or scale keeps the weight at the same temperature as the equipment. We also offer a huge selection of Laboratory Calibration Weights and Calibration Mass Sets with Calibration certification and NIST Traceable Calibration for lab balances at www.calibrationweight.com All calibration weights are not returnable. Once your order has been placed it CAN NOT be cancelled. Please carefully consider this prior to placing your order. The reason for this is these weights are custom manufactured and are certified on the date they were made. In addition, if you touch the calibration weight with your fingers the oil in your skin would change the tolerance and we can not take this chance if the weight was returned.
You May Also Like
You may also be interested in the following product(s)
21 piece (100g-1mg) nvlap weight set class 1 21 piece (100g-1mg) nvlap weight set class 1

MSRP: $2,239.00

YOU PAY: $1,955.00

nvlap 22 piece (200g-1mg) weight set class 1 nvlap 22 piece (200g-1mg) weight set class 1

MSRP: $2,381.00

YOU PAY: $2,080.00

500 mg class 1 calibration leaf weight 500 mg class 1 calibration leaf weight

MSRP: $125.00

YOU PAY: $103.00

100 gram lab balance calibration weight 100 gram lab balance calibration weight

MSRP: $80.00

YOU PAY: $68.00

1mg Leaf Weight 1mg Leaf Weight

MSRP: $125.00

YOU PAY: $103.00

nvlap 20 piece weight set(50g-1mg)class 1 nvlap 20 piece weight set(50g-1mg)class 1

MSRP: $2,094.00

YOU PAY: $1,829.00

9 piece (100g-1g) nvlap weight set class 1 9 piece (100g-1g) nvlap weight set class 1

MSRP: $1,293.00

YOU PAY: $1,042.00

10 gram Class 1 calibration weight 10 gram Class 1 calibration weight

MSRP: $145.00

YOU PAY: $125.00

50 gram lab scale calibration mass 50 gram lab scale calibration mass

MSRP: $69.00

YOU PAY: $62.00

20 milligram class 1 calibration leaf weight 20 milligram class 1 calibration leaf weight

MSRP: $125.00

YOU PAY: $103.00

Additional Info
Additional Info
Brand Troemner
Capacity x Readability No
Capacity x Readability (dual range) No
Readability No
Readability 2 No
Weight Modes No
Functions No
Features No
Legal for Trade N/A
Construction Alloy 8 Stainless Steel
Calibration No
Communication No
Platform size (inches) No
Power Requirements No
Manufacturer Warranty (years) No
Additional info No
Tags
Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Specs
Size: 50 g
Class: Class 1
Tolerance: 0.12 mg
Certification: NVLAP Accredited Certificate
Material: Troemner Alloy 8 highly polished stainless steel
Construction: 2 piece construction with handling knob.
Case: Polycarbonate case with red insert
What's included
Class 1 NVLAP certificate
Polycarbonate case
 
  Loading...